PROTECTIONALL
Clear matt protection
FAQ
 Coverage: 10 to 12m² (107 to 129ft2) per litre per coat. |
 Application temperature: +10°C to +35°C |
 Drying timeDust free: 1 hour / Touch dry: 3 to 4 hours / Sandable: 4 hours / Recoat: 4 to 12 hours / Dry: 24 hours / Full hardness: 2 weeks |
PROPERTIES
Hardwearing.
Colourless.
Odourless.
Resistant to light – Non-yellowing.
Non-slip.
All porous surfaces (see Restrictions)
Functions
- PROTECTIONALL® is a high performance, single pack, clear, water-based varnish based on acrylic and polyurethane resins.
Designed specifically for the protection of porous surfaces, PROTECTIONALL® provides strong protection against mechanical and chemical damage (detergents, hot oil, wine, etc.).
WHERE TO USE
- Any porous surface: Tiles, Wood, Cement, Concrete, Stone etc.
- Floors**, Panelling, Shelves, Furniture, Worktops, Walls etc.
- Matt painted surfaces.
** See Restrictions.
specifications
- Suitable for stone, cement and tiled flooring. For wooden floors use VEGAFLOOR.
SURFACE PREPARATION
- General Directions:
Surfaces must be clean, dry and free of dirt, dust, grease and any other surface contamination.
Clean and remove any stains. Any stains not removed and coated with PROTECTIONALL® will be permanently fixed.
Painted surfaces must be in good condition.
- Wooden Surfaces (Not Floors):
Sand with 80 or 120 grit abrasive.
Remove all sanding dust.
Wipe over with a Tack Cloth or cloth soaked in Methylated Spirits (Denatured Alcohol) to remove any remaining sanding residue.
- Painted Surfaces:
Clean painted surfaces with SOAPCLEAN or similar product, rinse and allow to dry.
Matt Finish: Abrade surface with fine grade (120 grit) sandpaper. Dust off.
Satin Finish: PROTECTIONALL® may only be applied to a poor-quality satin paint or a satin paint in very poor condition. Abrade surface with fine grade (120 grit) sandpaper. Dust off.
Gloss or Washable Finish: DO NOT use PROTECTIONALL®.
- Tile and Stone Surfaces:
Clean surfaces with SOAPCLEAN or similar product, rinse and allow to dry completely.
Check moisture content with a suitable moisture metre.
- Cement and Concrete Surfaces:
New Cement and Concrete: Allow to dry out a minimum of 3 months.
All new or unfinished cement and concrete should be suitably prepared and the alkalinity neutralised.
Ensure surface is completely dry.
Check moisture content with a suitable moisture metre.
Note: Polished or Power Floated concrete surfaces (floors, worktops etc.) should be Diamond Ground, Shot Blasted or Acid Etched prior to applying PROTECTIONALL®.
Application
- Use as is. Do not dilute.
- Stir PROTECTIONALL® thoroughly and gently. Do not shake.
- Start at the edges, then do the remaining surface, working in areas of no more than 2m x 2m.
- Always maintain a wet edge to avoid overlaps.
- Apply an even coat of PROTECTIONALL®. Do 3 criss-cross passes in one application, always finishing in the direction of the grain.
- Allow to dry.
- Sand surface with fine grade abrasive (150 to 180 grit). Thoroughly dust off.
- Apply 2nd coat of PROTECTIONALL®. Do not leave more than 12 hours between application of the 1st and 2nd coat and any subsequent coats.
Very Porous Surfaces:
- Apply a 3rd coat following directions above.
Exposed Surfaces e.g. Worktops, Table Top, Splashback….
- Apply 3 to 4 coats depending on use, following directions above.
Wait a minimum of 48 hours after finishing before replacing any furniture or heavy objects.
Do not cover the treated surface for at least 14 days after application.
Maintenance
- Renewal of PROTECTIONALL®. Normally every 5 to 10 years as required.
- Clean surface with SOAPCLEAN or similar product to remove all traces of wax, grease, dirt and any other surface contamination.
- Sand surface with fine grade abrasive (150 to 180 grit). Thoroughly dust off.
- Apply one coat of PROTECTIONALL®.
Proud Members of International Thermo Wood Association 
- Site created by adfields.solutions
© OWATROL - Groupe DURIEU - 29 avenue du Roule - 92200 Neuilly s/Seine (France) - Phone: +33 (0)1 82 88 83 65 - Fax : +33 (0) 160 86 84 84