search
search
This product is available in the following families
DEEP CLEANER
Oil remover & cleaner
 Coverage: 4 m²/l |
 Application temperature: +5°C to +35°C |
 Drying: N/A |
PROPERTIES
DEEP CLEANER is a powerful, water washable, solvent free remover and cleaner that strips out new, old and encrusted oils from exterior wooden surfaces and cleans severely weathered wood. Biodegradable, DEEP CLEANER is suitable for environmentally sensitive areas, while its gel consistency means it will not run, making it ideal for vertical surfaces.
Easy to apply and fast acting, DEEP CLEANER quickly and efficiently removes the millglaze, which is created in the manufacturing process, from the surface of new wood, thus improving the penetration and adhesion of a finish.
Functions
- Removes Teak and other oils from woods, blackened by UV rays.
- Water washable - Oils are dissolved in water.
- Deep cleans severely weathered wood.
- Removes Millglaze - Improves the penetration and bonding of a finish.
- Fast Acting - Works in as little as 5 minutes.
- Ready to use.
- Easy application.
- Removes lubricating oils and stains.
- Biodegradable - Does not contain solvent or paraffin.
WHERE TO USE
- Exterior use only.
- All exterior wood - Softwoods, Hardwoods - Exotic and Broad Leaved.
- Exterior wood surfaces - Decks, Handrails, Trim...
- Horizontal and vertical surfaces.
SURFACE PREPARATION
- Remove any loose and flaking finish.
- Brush off any physical surface contamination e.g. moss, general dirt etc.
RECOMMENDATIONS BEFORE Application
- Always carry out a preliminary test prior to commencing the job, to determine the contact time necessary for stripping or cleaning the wood. See test procedure.
- When stripping or cleaning areas that have caulking, ALWAYS carry out a test by applying DEEP CLEANER to a small area and allow it to sit for 20 minutes before scrubbing and rinsing off to determine that there is no reaction.
- Wear chemical resistant gloves, safety goggles and protective clothing.
- Always treat stripped and cleaned surfaces with DECK CLEANER to neutralise the surface and restore the woods colour.
- Woods rich in tannins e.g. Cedar, Oak, Teak, Mahogany... may darken with DEEP CLEANER. Where DEEP CLEANER has darkened the wood DO NOT allow it to dry, prior to using DECK CLEANER.
- Cover and protect everything you do not wish to strip or clean, including any aluminium surfaces.
- When stripping or cleaning vertical surfaces, work from bottom to top to avoid streaking.
- Apply between 5°C (41°F) and 35°C (95°F). Do not apply in direct sunlight or to a hot surface.
- Do not allow DEEP CLEANER to dry on the surface. If drying occurs dampen with a mist application of water.
- Consult us for additional information and advice prior to using DEEP CLEANER on Oak and Chestnut.
Application
- Use as is, Do Not dilute.
- Work large areas in zones.
- Always work in direction of the grain. Do Not use a wire brush.
- After rinsing, immediately treat surface with DECK CLEANER while still wet.
- Allow wood to dry thoroughly, 2-3 days before refinishing.
Test Procedure
- Apply DEEP CLEANER
- Allow to work 5 minutes.
- Scrub surface to see if finish or dirt is lifting.
- If lifting commence with job, if not wait a further 5 minutes and test again, continue this process up to a maximum of 20 minutes.
STRIPPING AND CLEANING
- Work in areas that can be completed in 5-20 minutes, then move on to the next area until entire surface is stripped or clean.
- Apply DEEP CLEANER to the area to be stripped or cleaned and allow to work.
- After time established in the test, scrub surface with a stiff nylon brush, if required flush with water at the same time OR use a power washer (max 60 bars/870 psi).
- Thoroughly rinse the surface after stripping/cleaning including any adjacent areas, with fresh clean water.
- NB: The use of hot water makes the job easier.
REDUCING MILLGLAZE
- Apply DEEP CLEANER to the area to be treated.
- Allow to work 10-15 minutes depending on wood type.
- Scrub surface with stiff nylon scrubbing brush, if required flush with water at the same time OR use a power washer (max 60 bars/870 psi).
- After removing the millglaze, thoroughly rinse the surface including any adjacent areas with fresh clean water.
Consult us for additional information and advice prior to using DEEP CLEANER on Oak and Chestnut.
Recommendations after Application
- Water
Maintenance
- Do not store in metal containers.
- Keep from freezing and high temperatures.
our Advice
- Always apply DECK CLEANER to neutralise the surface and restore the wood's colour.
Related Products
Proud Members of International Thermo Wood Association 
- Site created by adfields.solutions
© OWATROL - Groupe DURIEU - 29 avenue du Roule - 92200 Neuilly s/Seine (France) - Phone: +33 (0)1 82 88 83 65 - Fax : +33 (0) 160 86 84 84