TEAK PROTECT

Water based saturateur

Technical data sheet	FAQ
Safety data sheet	Where to find product

Application temperature : 10°C (50°F) and 30°C (86°F)

picto_eau-Gb

PROPERTIES

TEAKPROTECT is a penetrating wood finish that provides a flexible, long-lasting rich, matt finish for all woods. TEAKPROTECT saturates, penetrates and stabilises wood to minimise cracking, warping and other damage caused by moisture and sun.

Functions

Non-film forming - Will not peel or flake.
Apply to new or weathered wood.
Provides a matt finish that accentuates the beauty of wood.
Premium UV absorbing transoxide pigments - Provide a long lasting finish.
Maintains the natural look of the wood and Cork.
Allows Cork to breathe while protecting it from moisture.
Easy maintenance - No sanding or stripping.

WHERE TO USE

SURFACE PREPARATION

General Directions:

Surfaces must be thoroughly clean, dry and free of dirt, grease, grime, mildew and previous coatings.
Treat mildew with a 50/50 bleach/water solution. Scrub solution on to surface and allow to stand for 10-15 minutes; rinse thoroughly.
After cleaning and/or stripping, allow wood to dry 2-3 good drying days or until it has reached a moisture content of 18% or less before applying finish.
TEAKPROTECT can only be applied to bare wood surfaces or a weathered wood surface that was previously finished with TEAKPROTECT. ALL other finishes MUST be completely and thoroughly removed.
If necessary sand surface after cleaning and/or stripping (max 80 grit paper).

New wood surfaces:

New wood surfaces have a hard shiny surface called mill glaze that prevents maximum penetration and bonding of any finish; this should be removed prior to application in order to ensure maximum performance of the finish.
Treat with DEEP CLEANER*, neutralise with DECK CLEANER*, alternatively mechanically or manually abrade surface (max 80 grit paper). Clean off all loose wood particles. Test wood for absorbency by sprinkling water on the surface. If water is absorbed rapidly, the surface is ready for finishing, if not repeat process.

Untreated weathered woods:

Untreated wood surfaces that have weathered longer than 6 months should be thoroughly cleaned with undiluted DECK CLEANER* to ensure that all loose wood fibres, dirt and other surface contaminants are removed. For severely contaminated surfaces clean with DEEP CLEANER, neutralise with DECK CLEANER.

Previously coated surfaces (oiled, paint, stain, varnish....):

All previous coatings must be completely and thoroughly removed.
Oils and sealers: Strip with DEEP CLEANER*, neutralise with DECK CLEANER*.
Oil/Alkyd based finishes: Strip with MARINE STRIP, neutralise with DECK CLEANER*.
Acrylic finishes: Contact us.
Other finishes e.g. 2 pack Epoxies, Urethanes.... Strip with DSP 800*.

Note: Hardwoods and woods rich in tannins e.g. Oak, Cedar, Teak, Ipe.... may darken with DEEP CLEANER* AND MARINE STRIP*, neutralising with DECK CLEANER* immediately after rinsing will lighten and restore the woods colour.

RECOMMENDATIONS BEFORE Application

Application

Maintenance

our Advice

Color available

– / 2

Related Products

DECK CLEANER

Cleaner & Brightener

MARINE STRIP

Gel remover - Water washable

DEEP CLEANER

Oil remover & cleaner

If you require a more comprehensive recommendation please complete the request form by clicking on this link

Proud Members of International Thermo Wood Association - Site created by adfields.solutions
© OWATROL - Groupe DURIEU - 29 avenue du Roule - 92200 Neuilly s/Seine (France) - Phone: +33 (0)1 82 88 83 65 - Fax : +33 (0) 160 86 84 84

Navigation menu

search

TEAK PROTECT

PROPERTIES

Functions

WHERE TO USE

SURFACE PREPARATION

RECOMMENDATIONS BEFORE Application

Application

Maintenance

our Advice

Color available

Related Products

DECK CLEANER

MARINE STRIP

DEEP CLEANER

Also find

Direct access

Community

To be known

Tools