Copie de MARINE OIL ES
Acondicionador & inhibidor de óxido
 Coverage: 18 m²/l |
 Application temperature: +5°C to +35°C |
 Drying: 24 h |
PROPERTIES
MARINE OIL is a versatile, highly penetrating air drying oil that can be used alone or added to paint. Used alone it provides a tough, flexible finish, driving out excess moisture and air; displacing it from rusted metal, so stopping rust. Filling dry porous wood to stop paint peeling. Added to any oil or alkyd based coatings and it will give increased wet edge time, improved flow ability, greater adhesion and unlike damaging thinners, will maintain the inherent quality of the paint without affecting its appearance or drying times.
Functions
- Apply directly to rusted surfaces.
- Penetrates deep in to rusted surfaces to drive out moisture and air.
- Forms a solid stable layer that other paints can firmly adhere to.
- Completely seals sound underlying metal against corrosion.
- Compatible with all oil and alkyd based paints.
- Use on non-ferrous metals - Zinc, Copper, Aluminium...
- Primer for Galvanised surfaces - No weathering or pickling required.
- Additive for all oil/alkyd based paints, stains and varnishes include urethane alkyd paints.
- Fills woods pores with oil - Prevents paint peeling.
- Assures better adhesion of finishes.
- Eases application of finishes in difficult conditions.
- Overcoat with DEKS OLJE D.2* on rusted surfaces for a high gloss rusted look.
- Improved flow ability - Increased wet edge time.
WHERE TO USE
- Interior and exterior use.
- Steel structures, railings, pipes, grills, stairs...
- Machinery, engine parts, trailers...
- Hulls, tanks...
- All Wood surfaces, dry, porous, soft & punky...
- Horizontal and vertical surfaces.
SURFACE PREPARATION
PAINT CONDITIONER
- Prepare surface as per instructions on the paint can.
- Remove all loose and flaking material.
- Treat any organic growth with fungicidal solution or a mix of 1 part water to 1 part chlorine bleach (allow bleach solution to sit for 15 minutes), rinse thoroughly and allow to dry.
RUST INHIBITOR
- Surfaces must be clean, dry and free from oil, grease and other surface contaminants.
- Remove all scale; loose and flaking rust and old paint back to a sound surface and edge.
- Feather in any sharp edges.
- Surfaces exposed to chemicals (acids, alkalis or salt deposits) should be washed using copious amounts of water or steam cleaned. Allow to fully dry.
- Severely contaminated surfaces should be cleaned using an appropriate solvent e.g. Acetone.
- Do not remove firm rust.
- Do not clean metal back to a bright finish.
RECOMMENDATIONS BEFORE Application
- Cover everything you do not wish to paint.
- Apply between +5°C and +35°C.
- Do not apply in direct sunlight or to hot surfaces.
- Test for compatibility when adding MARINE OIL to paint.
Application
PAINT CONDITIONER
- Apply paint in normal manner.
- If paint is sticky, drags, sets up to fast or does not level properly add MARINE OIL (stirring in well) until the paint works smoothly, easily and evenly. Allow the brush, roller or sprayer to be your guide.
- Mixing instructions
- Topcoat: As required. Normally 5%-20% by volume.
- Undercoat: up to 30% by volume.
- Primer: up to 50% by volume.
- The above is meant as a guide only. Conditions of application, porosity of surface etc. will dictate the amount of MARINE OIL to be mixed into the paint.
- Wood surfaces in sound condition
- Prime any bare wood with a mix of 1 part MARINE OIL to 2 parts primer. Allow to dry.
- Follow with normal paint system adding MARINE OIL as in "Mixing Instructions" above.
- Damaged, soft or punky wood surfaces
- Apply 2 to 4 liberal applications of MARINE OIL wet on wet, as fast as the wood will absorb it.
- Do not allow MARINE OIL to dry between applications.
- When the wood cannot absorb any more wipe up any excess and allow to dry overnight (12 hrs).
- Follow with normal paint system adding MARINE OIL as in "Mixing Instructions" above to ease application and aid adhesion.
RUST INHIBITOR
- New clean steel
- Prime new steel with a mix of 1 part MARINE OIL to 3 parts primer.
- Follow with normal paint system adding MARINE OIL to subsequent coats as directed under "Mixing instructions".
- Lightly rusted surfaces
- Prime surface with a mix of 1 part MARINE OIL to 2 parts primer.
- Follow with normal paint system adding MARINE OIL to subsequent coats as directed under "Mixing instructions".
- New unpainted rusty steel
- Prime surface with a mix of 1 part MARINE OIL to 1 part Primer.
- Follow with normal paint system adding MARINE OIL to subsequent coats as directed under "Mixing instructions".
- Old severely rusted or previously coated surfaces
- Apply wet on wet applications of MARINE OIL to all exposed rust until fully saturated and allow to dry.
- Saturation is indicated by a uniform glossy appearance to the surface when OWATROL® OIL is dry.
- Before MARINE OIL has hardened, check surfaces and remove rust scale and old paint loosened by the above. If needed, touch up these areas. Allow to dry.
- Apply a mix of 1 part MARINE OIL to 2 parts primer. Allow to dry.
- Follow with normal paint system adding MARINE OIL to subsequent coats as directed under "Mixing instructions".
- Note: MARINE OIL will not lift well bonded paint.
Recommendations after Application
- Clean all tools and equipment with White (mineral) Spirits while still wet. If allowed to dry, remove with paint stripper. Store and maintain equipment as directed by manufacturer.
Note: Any rags, steel wool etc. soaked in MARINE OIL may spontaneously catch fire if improperly discarded. Rags, steel wool etc. must be saturated with water after use or placed in a sealed, water filled metal container, before disposing with household waste. Rags may be laid flat and air dried before discarding.
Related Products
Proud Members of International Thermo Wood Association 
- Site created by adfields.solutions
© OWATROL - Groupe DURIEU - 29 avenue du Roule - 92200 Neuilly s/Seine (France) - Phone: +33 (0)1 82 88 83 65 - Fax : +33 (0) 160 86 84 84