Our solutions
BAFHBK
BAFHBKen
Ensure weather conditions are compatible with application of the product.
The surface must be clean, dry and in sound condition.
PREPARATION: 2 options available for stripping back to bare wood: 1- Apply DSP 800. Allow it to work according to test previously conducted to strip finish. When the coating curls or softens, remove finish with a scraper or a nylon scrubbing brush. Rinse the surface with warm water, acetone or white spirit to remove any waxz residue. 2-Sand the surface. Finish by sanding with 80/100 grit max. Thoroughly dust off.
APPLICATION: Thoroughly stir ANTISLIP. Apply one coat; allow to dry 6 hours minimum, apply second coat. Allow to dry 24 hours.
The surface must be clean, dry and in sound condition.
PREPARATION: 2 options available for stripping back to bare wood: 1- Apply DSP 800. Allow it to work according to test previously conducted to strip finish. When the coating curls or softens, remove finish with a scraper or a nylon scrubbing brush. Rinse the surface with warm water, acetone or white spirit to remove any waxz residue. 2-Sand the surface. Finish by sanding with 80/100 grit max. Thoroughly dust off.
APPLICATION: Thoroughly stir ANTISLIP. Apply one coat; allow to dry 6 hours minimum, apply second coat. Allow to dry 24 hours.
BAFHEA
BAFHEAen
Ensure weather conditions are compatible with application of the product.
The surface must be clean, dry and in sound condition.
PREPARATION: 2 options available for stripping back to bare wood: 1- Apply DSP 800. Allow it to work according to test previously conducted to strip finish. When the coating curls or softens, remove finish with a scraper or a nylon scrubbing brush. Rinse the surface with warm water, acetone or white spirit to remove any waxz residue. 2-Sand the surface. Finish by sanding with 80/100 grit max. Thoroughly dust off.
APPLICATION: Apply a generous and even application coat of H4 WOOD. Allow to dry 24 hours.
The surface must be clean, dry and in sound condition.
PREPARATION: 2 options available for stripping back to bare wood: 1- Apply DSP 800. Allow it to work according to test previously conducted to strip finish. When the coating curls or softens, remove finish with a scraper or a nylon scrubbing brush. Rinse the surface with warm water, acetone or white spirit to remove any waxz residue. 2-Sand the surface. Finish by sanding with 80/100 grit max. Thoroughly dust off.
APPLICATION: Apply a generous and even application coat of H4 WOOD. Allow to dry 24 hours.
BAFHFG
BAFHFGen
Ensure weather conditions are compatible with application of the product.
The surface must be clean, dry and in sound condition.
PREPARATION: 2 options available for stripping back to bare wood: 1- Apply DSP 800. Allow it to work according to test previously conducted to strip finish. When the coating curls or softens, remove finish with a scraper or a nylon scrubbing brush. Rinse the surface with warm water, acetone or white spirit to remove any waxz residue. 2-Sand the surface. Finish by sanding with 80/100 grit max. Thoroughly dust off.
APPLICATION: Apply one coat of SOLID COLOR STAIN, allow to dry 4 hours. Apply second coat. Allow to dry 24 hours without rain.
The surface must be clean, dry and in sound condition.
PREPARATION: 2 options available for stripping back to bare wood: 1- Apply DSP 800. Allow it to work according to test previously conducted to strip finish. When the coating curls or softens, remove finish with a scraper or a nylon scrubbing brush. Rinse the surface with warm water, acetone or white spirit to remove any waxz residue. 2-Sand the surface. Finish by sanding with 80/100 grit max. Thoroughly dust off.
APPLICATION: Apply one coat of SOLID COLOR STAIN, allow to dry 4 hours. Apply second coat. Allow to dry 24 hours without rain.
BAGAAA
BAGAAAen
Ensure weather conditions are compatible with application of the product.
The surface must be clean, dry and in sound condition.
PREPARATION: Conduct a water drop test: sprinkle a few drops of water on the wood. If water penetrates quickly the finish can be applied. If the water sits on the surface or beads up then the grain of the wood is not sufficienlty open to apply the finish. It is then necessary to prepare it with one of three solutions: 1-Sand the wood with (grit 80/100 max) abrasive. Thoroughly dust off. 2-For direct application, apply AQUANETT to dry wood. Scrub with a synthetic brush, allow it to stand 5min, rinse with fresh water. After rinsing immediately apply NET-TROL to the wet wood. Scrub with a synthetic brush, allow it stand between 10 and 30min, rinse with fresh water. Allow wood to dry 3 good drying days before applying the finish. 3-For a deferred application (except if applying AQUADECKS or TROPITECH ALL IN ONE), apply one coat of SEASONITE to wood that is touch dry. Allow wood to weather between 6 and 12 months. Clean with NET-TROL, rinse with fresh water. Allow wood to dry 3 good drying days before applying finish.
APPLICATION: Apply one coat of AQUATROL clear, allow it to penetrate 15-30min max, apply second coat. Allow it to penetrate. Wipe off or brush out excess product to avoid it drying as a shiny finish on the surface. Allow to dry 24 hours without rain.
The surface must be clean, dry and in sound condition.
PREPARATION: Conduct a water drop test: sprinkle a few drops of water on the wood. If water penetrates quickly the finish can be applied. If the water sits on the surface or beads up then the grain of the wood is not sufficienlty open to apply the finish. It is then necessary to prepare it with one of three solutions: 1-Sand the wood with (grit 80/100 max) abrasive. Thoroughly dust off. 2-For direct application, apply AQUANETT to dry wood. Scrub with a synthetic brush, allow it to stand 5min, rinse with fresh water. After rinsing immediately apply NET-TROL to the wet wood. Scrub with a synthetic brush, allow it stand between 10 and 30min, rinse with fresh water. Allow wood to dry 3 good drying days before applying the finish. 3-For a deferred application (except if applying AQUADECKS or TROPITECH ALL IN ONE), apply one coat of SEASONITE to wood that is touch dry. Allow wood to weather between 6 and 12 months. Clean with NET-TROL, rinse with fresh water. Allow wood to dry 3 good drying days before applying finish.
APPLICATION: Apply one coat of AQUATROL clear, allow it to penetrate 15-30min max, apply second coat. Allow it to penetrate. Wipe off or brush out excess product to avoid it drying as a shiny finish on the surface. Allow to dry 24 hours without rain.
BAGAAD
BAGAADen
Ensure weather conditions are compatible with application of the product.
The surface must be clean, dry and in sound condition.
PREPARATION: Conduct a water drop test: sprinkle a few drops of water on the wood. If water penetrates quickly the finish can be applied. If the water sits on the surface or beads up then the grain of the wood is not sufficienlty open to apply the finish. It is then necessary to prepare it with one of three solutions: 1-Sand the wood with (grit 80/100 max) abrasive. Thoroughly dust off. 2-For direct application, apply AQUANETT to dry wood. Scrub with a synthetic brush, allow it to stand 5min, rinse with fresh water. After rinsing immediately apply NET-TROL to the wet wood. Scrub with a synthetic brush, allow it stand between 10 and 30min, rinse with fresh water. Allow wood to dry 3 good drying days before applying the finish. 3-For a deferred application (except if applying AQUADECKS or TROPITECH ALL IN ONE), apply one coat of SEASONITE to wood that is touch dry. Allow wood to weather between 6 and 12 months. Clean with NET-TROL, rinse with fresh water. Allow wood to dry 3 good drying days before applying finish.
APPLICATION: Apply one coat of AQUADECKS, allow it to penetrate 15-30min max, apply second coat. Allow it to penetrate. Wipe off or brush out excess product to avoid it drying as a shiny finish on the surface. Allow to dry 12 hours without rain.
The surface must be clean, dry and in sound condition.
PREPARATION: Conduct a water drop test: sprinkle a few drops of water on the wood. If water penetrates quickly the finish can be applied. If the water sits on the surface or beads up then the grain of the wood is not sufficienlty open to apply the finish. It is then necessary to prepare it with one of three solutions: 1-Sand the wood with (grit 80/100 max) abrasive. Thoroughly dust off. 2-For direct application, apply AQUANETT to dry wood. Scrub with a synthetic brush, allow it to stand 5min, rinse with fresh water. After rinsing immediately apply NET-TROL to the wet wood. Scrub with a synthetic brush, allow it stand between 10 and 30min, rinse with fresh water. Allow wood to dry 3 good drying days before applying the finish. 3-For a deferred application (except if applying AQUADECKS or TROPITECH ALL IN ONE), apply one coat of SEASONITE to wood that is touch dry. Allow wood to weather between 6 and 12 months. Clean with NET-TROL, rinse with fresh water. Allow wood to dry 3 good drying days before applying finish.
APPLICATION: Apply one coat of AQUADECKS, allow it to penetrate 15-30min max, apply second coat. Allow it to penetrate. Wipe off or brush out excess product to avoid it drying as a shiny finish on the surface. Allow to dry 12 hours without rain.
Proud Members of International Thermo Wood Association 
- Site created by adfields.solutions
© OWATROL - Groupe DURIEU - 29 avenue du Roule - 92200 Neuilly s/Seine (France) - Phone: +33 (0)1 82 88 83 65 - Fax : +33 (0) 160 86 84 84