OWAGRIP

Anti-slip polyurethane marine paint

Technical data sheet	FAQ
Safety data sheet	Where to find product

Application temperature: + 5 ° C to + 30 ° C

picto_eau-Gb

PROPERTIES

One pack polyurethane non-slip paint, for Metal, Wood, Gelcoat and Aluminum.
Anti-corrosive and UV resistant.
Limits glare from the sun.
High resistance to abrasion and saline conditions. Excellent colour fastness
Easy to apply: Brush or roller depending on the surface
Satin finish, Limits accumulation of dirt and eases cleaning.

WHERE TO USE

Interior and exterior
Wood, new or rusted metal, Aluminum, Gelcoat, previously painted surfaces.
Excellent resistance to foot traffic and severe climatic conditions.
Apply to Gelcoat, previously painted surfaces, Metal, Aluminum and Wood.

SURFACE PREPARATION

The surface must be clean, dry, degreased and free of any preparation residue. Drying times given are based on 20°C. at 50% RH. If the atmospheric conditions are lower than this then the overcoating and drying times should be adapted to take this into account.

Painted surfaces (PU, Epoxy, Alkyd, Acrylic) in good condition:

Clean / degrease the surface with OWACLEAN. Rinse thoroughly and allow to dry. Sand 80/100 grit paper. Dust off.
Apply 2 coats of OWAGRIP.

Painted surfaces in poor condition and poorly adhered:

Remove old coating back to the bare surface by chemically stripping or mechanical abrasion.
Clean surface of all preparation residue
Degrease with OWACLEAN.
Rinse well and allow to dry
Apply 1 coat of PID60 MARINE primer.
Allow to dry for 2 to 4 hours.
Apply 2 coats of OWAGRIP.

Bare wood surface:

Degrease oily woods e.g. new Teak with acetone or similar.
Sand with 80/100 grit paper. Dust off.
Apply a coat of OWAGRIP diluted 15% with OWATROL OIL or MARINE OIL. Allow to dry.
Apply a 2nd coat of undiluted OWAGRIP.

Bare new metal:

Degrease with OWACLEAN or other sutiable cleaning agent e.g. Acetone.
Grind (P24 / P36) or sand (40-120 grit).
Clean and allow to dry. Hard to reach areas may be prepared using OWAYELL (1 part OWAYELL to 5 parts water). Leave for 10 minutes and rinse thoroughly.
Apply 1 coat of PID 60 MARINE primer. Allow to dry 2 to 4 hours.
Apply 2 coats of OWAGRIP.

Rusty Metal

Light or moderate rust:
Degrease with OWACLEAN or other sutiable cleaning agent e.g. Acetone.
Remove all loose and flaking rust
Dust off.
Saturate surface with OWATROL OIL or MARINE OIL. Allow to dry, 24 to 72 hours.
Apply a coat of OWAGRIP diluted 15% with OWATROL OIL or MARINE OIL. Allow to dry.
Apply a 2nd coat of undiluted OWAGRIP.

Heavy or severe rust:

Blast, Grind, Sand or use undiluted OWAYELL to remove all rust back to bare clean metal.
Clean thoroughly and allow to dry.
Degrease with OWACLEAN or other suitable cleaning agent e.g. Acetone.
Apply 1 coat of PID 60 MARINE primer. Allow to dry 2 to 4 hours.
Apply 2 coats of OWAGRIP.

Aluminum:

Degrease with OWACLEAN or Acetone.
Sand with 24-120 grit paper compatible with aluminium.
Clean thoroughly and allow to dry. Hard to reach areas may be prepared using OWAYELL (1 part OWAYELL to 5 parts water). Leave for 10 minutes and rinse thoroughly.
Apply 1 coat of PID 60 MARINE primer. Allow to dry 2 to 4 hours.
Apply 2 or 3 coats of OWAGRIP.

New Gelcoat

Remove all traces of silicone, wax, etc. with Acetone.
Clean with OWACLEAN or detergent. Allow to dry.
Sand with a 180-220 grit paper. Clean thoroughly and allow to dry.
Apply 1 coat of PID 60 MARINE primer. Allow to dry 2 to 4 hours.
Apply 2 or 3 coats of OWAGRIP.

Used Gelcoat

Clean with OWACLEAN or a detergent. Let dry.
Sand with 180-220 grit paper. Thoroughly clean and allow to dry.
Apply 1 coat of PID 60 MARINE primer. Allow to dry 2 to 4 hours.
Apply 2 or 3 coats of OWAGRIP.

RECOMMENDATIONS BEFORE Application

Application

our Advice

picto_phrase_obligatoires Dangerous. Observe any precautions for use. The instructions mentioned herein are indicative only. Please refer to the Technical Data Sheet for detailed instructions.

Related Products

PID 60 Marine

Anti-rust primer and bonding coat

OWATROL-GLV

Anti-corrosive galvanised appearance

MARINE POLYTROL

Removes rust from stainless steel - Revives dull and faded gelcoats

If you require a more comprehensive recommendation please complete the request form by clicking on this link

Proud Members of International Thermo Wood Association - Site created by adfields.solutions
© OWATROL - Groupe DURIEU - 29 avenue du Roule - 92200 Neuilly s/Seine (France) - Phone: +33 (0)1 82 88 83 65 - Fax : +33 (0) 160 86 84 84

Navigation menu

search

OWAGRIP

PROPERTIES

WHERE TO USE

SURFACE PREPARATION

RECOMMENDATIONS BEFORE Application

Application

our Advice

Related Products

PID 60 Marine

OWATROL-GLV

MARINE POLYTROL

Also find

Direct access

Community

To be known

Tools