OWALAK MARINE
Premium marine enamel
 Coverage: 10 m²/l per coat |
 Application temperature: +5°C to +35°C |
 Drying time (Touch dry): 4 hours - Recoat: 8 to 12 hours - Full Dry: 12 hours |
PROPERTIES
OWALAK MARINE is a premium, high gloss marine enamel for use on all substrates above the waterline. Long lasting, OWALAK MARINE is resistant to salt and pollutants while also possessing excellent flexibility and UV resistance. Easy to apply, OWALAK MARINE ensures an exceptional finish.
Functions
- Excellent colour and gloss retention.
- Specially formulated for extreme weather conditions.
- Excellent UV and Anti-corrosive properties.
- Renews, protects and decorates dull surfaces.
- Good mechanical and chemical resistance.
- Excellent flexibility and adhesion on all surfaces.
- Easy application. Easy clean.
WHERE TO USE
- Interior and Exterior.
- All Surfaces above the waterline.
- Metal (Aluminium, Steel, Galvanised steel, etc.), Painted surfaces, Wood, Gelcoat….
- Previously painted surfaces - Polyurethane, Epoxy, Alkyd, Acrylic….
- Pipes, Machinery, Superstructures, Handrails, Cabins….
SURFACE PREPARATION
Surfaces must be clean, dry, in sound condition and free of oil, grease and other surface contamination including any preparation residue e.g. blasting, sanding etc. before applying OWALAK MARINE.
Prior to blasting or manually preparing the surface all salt contamination should be removed using fresh water and the surface allowed to dry. All oils, grease etc. must be thoroughly removed using a suitable cleaning solvent e.g. OWACLEAN, Acetone. Deposits firmly adhered should first be removed by scraping and then cleaned using the solvent.
- Painted Surfaces
Conduct adhesion test using the Cross Hatch method.
Coating in Good Condition and Well Adhered
Clean surface with OWACLEAN or other suitable cleaning agent.
Sand surface with 80-100 grit abrasive paper feathering in any sharp edges. Dust off.
Wood – Spot prime any bare areas with OWALAK MARINE plus 25% MARINE OIL.
Metal, Gelcoat etc. – Spot prime any bare areas with PID 60 MARINE.
Coating in Poor Condition and Poorly Adhered
Strip surfaces with DSP 800, MARINE STRIP or by mechanical abrasion.
Sand surface with 80-100 grit abrasive paper. Dust off.
Wood – Prime with OWALAK MARINE plus 25% MARINE OIL.
Metal, Gelcoat etc. – Prime surface with PID 30 or PID 60 MARINE.
The information set out cons are purely illustrative and are not the responsibility of the manufacturer, the application of products not made under his supervision.
- Uncoated Wooden Surfaces
New:
Treat with DEEP CLEANER, Neutralise with DECK CLEANER. Alternatively sand surface with 80 grit (max) abrasive paper.
Dust off and wipe surface with a cloth soaked in Acetone, Methylated Spirits, or similar (NOT White Spirit) to remove any remaining sanding residue and degrease the surface.
Weathered Wood
Clean with DECK CLEANER or thoroughly sand with coarse abrasive paper to remove all signs of dead denatured wood fibres.
Sand surface with 80-100 grit abrasive paper to smooth off.
Dust off and wipe surface with a cloth soaked in Acetone, Methylated Spirits, or similar (NOT White Spirit) to remove any remaining sanding residue and degrease the surface.
Prime, prepared new/weathered wood with OWALAK MARINE plus 25% MARINE OIL.
Allow to dry 24 hours.
- New Metal Surfaces exc. Aluminium
Clean surface with OWACLEAN or other suitable cleaning agent.
Blast, grind (P24-P36) or sand (40-120 grit) surface.
Inaccessible areas may be prepared using diluted OWAYELL.
Prime surface with PID 30 or PID 60 MARINE.
- Rusted Metal Surfaces
Light to Moderate Rust:
Remove all loose and flaking rust.
Clean surface with OWACLEAN or other suitable cleaning agent.
Saturate surface with MARINE OIL.
Allow to dry 24 -72 hours.
Heavy to Severe Rust:
Clean surface with OWACLEAN or other suitable cleaning agent.
Blast, grind (P24-P36) or sand (40-120 grit) to remove all rust back to bare clean metal.
Inaccessible areas may be prepared using undiluted OWAYELL.
Prime surface with PID30 or PID 60 MARINE.
- Aluminium:
Clean surface with OWACLEAN or Acetone.
Blast or sand surface with 24-120 grit paper.
Inaccessible areas may be prepared using diluted OWAYELL
Prime with PID30 or PID 60 MARINE.
- Gelcoat/Plastic:
Remove all traces of silicone, wax, paraffin etc. with Acetone.
Clean surface with OWACLEAN or hot soapy water.
Rinse thoroughly and allow to dry.
Sand with 180-220 grit sanding discs.
Prime surface with PID 30 or PID 60 MARINE.
Application
- Stir product well before and during use.
- Do not thin unless otherwise indicated.
- Apply 2 or 3 even coats allowing drying time between each coat.
Optional:
- Brush/Roller application – 5% MARINE OIL may be added to the 1st finish coat.
- Spray application – 5% MARINE OIL or White Spirit may be added to ease application.
Related Products
Proud Members of International Thermo Wood Association 
- Site created by adfields.solutions
© OWATROL - Groupe DURIEU - 29 avenue du Roule - 92200 Neuilly s/Seine (France) - Phone: +33 (0)1 82 88 83 65 - Fax : +33 (0) 160 86 84 84